-
As it says,a xs650 roller that I was going to hard tail,but plans have changed.What you see is what you get.Most chrome should clean up,19"front wheel and 16"rear wheel.Bike was a disc brake front and rear.Would be a nice start for a bobber!I am d...3 weeks ago on AmericanlistedTools
-
Can be rebuilt with tender loving care or can used as a parts bike. It has been sitting for 26 years under a tarp. Does not run. Rusty. See photos for condition. I can send more photos or answer questions about condition. Sold "as is" with no impl...Over 4 weeks ago on AmericanlistedTools
-
79 400 ltd 12k miles, hasn"t ran in ten years, flushed tank, installed new petcock, cleaned carbs, installed new diapragms, needle valves. changed plugs, points , condenser, coil, battery, new seatcover, still not running, maybe bad cdi box or sta...Over 4 weeks ago on AmericanlistedTools
-
As it says,a xs650 roller that I was going to hard tail,but plans have changed.What you see is what you get.Has no title,but do have the wa.plate that was on the bike,so getting a duplicate title should be easy,otherwise,I can register it in Idaho...Over 4 weeks ago on AmericanlistedTools
-
As it says,a xs650 roller that I was going to hard tail,but plans have changed.What you see is what you get.Most chrome should clean up,19"front wheel and 16"rear wheel.Bike was a disc brake front and rear.Would be a nice start for a bobber!I am d...Over 4 weeks ago on AmericanlistedTools
-
1979 BMW 100 Rt in Barn for 18 Yrs New Brakes, Brake Lines, Seat, Shocks, All rest original Very Very Nice Now Running Strong,.. Still need a bit of work.but very road worthy Sell, trade for what have youOver 4 weeks ago on AmericanlistedTools
-
1976/1979 Husqvarna Clutch Cover ,may fit other years, Small hairline crack, probably caused by the shift lever on the inside about 3/4 of an inch long. I also noticed a star crack ( like the kind that you get on your car windshield)probably cause...Over 4 weeks ago on AmericanlistedTools
-
Honda front motorcycle fender. Should fit the following Honda motorcycle models - 1979 or 1980 CB750 or CB750K or CB750F or CB750C. May also fit other Honda models and years including CB550 and CB650. Does not fit CB900. Probable part numbers are ...Over 4 weeks ago on AmericanlistedTools
-
I have a Honda CB400a "Hondamatic" motorcycle without a title. I am selling it as a parts bike. This is the bike that has an automatic transmission with a high and low range - no clutch. It last ran in 2010 and has been sitting ever since. Mechani...Over 4 weeks ago on AmericanlistedTools
-
1979 Honda XR80, great bike for a beginner just learning to ride. Has had a carb rebuild, a kill-switch added, new throttle cable, new brake and clutch levers, and kickstarter rubber The bike does run and will start, just needs a tune up and you c...Over 4 weeks ago on AmericanlistedTools
-
I have a 1979 Yamaha xs400 for sale. It has no title. It ran great started on the first kick every time. Then the wires in the handle bar switch started to smoke. Now for some reason I'm sure it's something minor it only has 82xxx miles on it. Sti...Over 4 weeks ago on AmericanlistedTools
-
New tires/parts and pre-owned 80s Jap Parts & VFR1000 Sprocket Carrier - $85 (NO PORTLAND NR 122nd & Airport Way)Brand New Tires and thousands of NEW & PRE-OWNED PARTS Fronts and Rears call 503 756 XXXX ..As we serve our Distributors PROUDLY!!Moun...Over 4 weeks ago on AmericanlistedTools
-
I have a 1979 motobecan for sale. its a must see . runs great. no rust has all parts that came w/ it like off the line..plus i have saddel bags for it.. can call for a piicture....Over 4 weeks ago on AmericanlistedTools
-
Description Mileage: 0 miles 1979 Honda ATC 110.?.good shape for the age of it. And it just needs a fuel a tank. On eBay they go for $10.00 - $110.00. Comes with many extra parts and extra tires. $150.00 call 305-508-XXXXOver 4 weeks ago on AmericanlistedTools
-
selling my xs650 cuz i have no time to work on it anymore... has a clean an clear title. was gonna do a bobber or cafe project but never got around to it. sellin cheap cuz it runs rough and i cant get it into first gear, possibly a bent shift fork...Over 4 weeks ago on AmericanlistedTools
