-
I purchased this bike in 1993 from USC Kawasaki. After years of occasional rides I had the bike disassembled by TJ Cycles in Austin in 1997 and powder coated the frame and did a minor restoration. In 1999 I took the bike to Kawasaki of Irving Texa...Over 4 weeks ago on Yupyi!Tools
-
Original paint on tank and right side cover. Engine rebuilt in 1985 with a new crankshaft and has 2500 miles on it. Bike has been in storage since 95â until 2019 and has since been restored to present condition with all new rubber components in...Over 4 weeks ago on Yupyi!Tools
-
This bike was acquired last year and I have done a complete restoration. The rims and spokes are new, OE style in front and rear. New Dunlop tires, tubes and rim protectors. The frame and swing arm are powder coated. The carburetors ( jetting 112....Over 4 weeks ago on Yupyi!Tools
-
Very early, very rare, 1973 Z1. This motorcycle will run. It has a very low serial number. I've had this motorcycle for at least six or seven years. The motor is not locked up and it did run when I first got it and it has been kept inside. Exccell...Over 4 weeks ago on Yupyi!Tools
-
This is a very nice 1974 Kawasaki Z1 This bike has 31,520 miles on it. The bike starts right up with a little choke, and settles into a nice idle after a brief warm up. The Vance Hines header sounds very nice. The paint and chrome look good, with ...Over 4 weeks ago on Yupyi!Tools
-
This is a low mileage 1975 Kawasaki H2 factory matching #s motorcycle. I has had a recent restoration which include a frame up reconditioning. This H2 750 performs and rides as it should. Service performed: *Reconditioned frame. *Rebuilt engine-Al...Over 4 weeks ago on Yupyi!Tools
-
This beautiful H2 was restored to ride and enjoy. The frame was powder coated and new paint and polishing everywhere. The frame tag was destroyed by the powder coat. The original stamp matches the title and goes with the engine number. What you se...Over 4 weeks ago on Yupyi!Tools
-
Kawasaki 900 Z1 , great running condition, new chain, new ltd seat, new front fork seals ,fresh engine rebuilt. Recent new rear tire, rear drum pads, brakes good ,new battery, new Accell high performance coils, fresh rebuilt Mikuni 29mm carburetor...Over 4 weeks ago on Yupyi!Tools
-
Bike runs good, chrome is nice, just a few minor pits on the rims, new fenders, new grab bar, original controls are nice, new master cylinder, new tins from z1parts.net, new seat, new shocks, new tires, nice kerker pipe, has original tool kit, no ...Over 4 weeks ago on Yupyi!Tools
-
This is a very nice restored Avenger. It starts easy and runs and rides as it should. I purchased it from a 71 year old ex dealer trained mechanic who restored it. He said the engine has been completely gone through- new crank seals etc and I am p...Over 4 weeks ago on Yupyi!Tools
-
748cc, 70hp+ triple that completed the quarter mile in 12.0 seconds flat in 1972... This left the rest of the industry picking their jaws up off the floor. If you are looking of the baddest of the bad street bike from the early-70's, these H2's ar...Over 4 weeks ago on Yupyi!Tools
-
Honest, original 1970 Kawasaki Triple All original paint except battery side cover. Fresh top end and carburetors rebuilt. Currently runs well with original ignition system , stock air box and clutch is new. Throttle and clutch cables have been re...Over 4 weeks ago on Yupyi!Tools
-
For sale is my beautiful 1974 Kawasaki Z1, true 70âs muscle bike. Always gets a ton of attention at bike night. Matching numbers engine to the frame being only 31 numbers off. Built in late 1973 makes this a early 1974. It has had many upgrades...Over 4 weeks ago on Yupyi!Tools
-
Details: Original Stock Paint - excellent condition. Original OEM Parts on bike, including original exhaust, runs amazing! Unrestored- we only kept in cleaned up Garaged / showroom stored No rust in fuel tank 15,629 original miles Full service his...Over 4 weeks ago on Yupyi!Tools
-
1974 Kawasaki Z1 900 95% done runs/ rides/ shift etc engine is completely rebuilt welded crank etc along with carbs , but needs finish work such as ,fork reflector ( found it ) , tach harness , instrument cluster harness , horn and some minor stuf...Over 4 weeks ago on Yupyi!Tools
