-
I shortened the sub frame and removed the tabs and bosses no longer needed. The frame was then sprayed gloss black. I disassembled the wheels and had the rims powder coated flat black, the hubs and spokes were cleaned and inspected and then the wh...2 weeks ago on AmericanlistedTools
-
The bike has a 5 speed gear cluster hidden in the original 4 speed transmission case. The cluster was made for this bike in England and installed here. This enables it to cruise the freeways at about 3000 rpm at 73mph. The 5th speed is an overdriv...3 weeks ago on AmericanlistedTools
-
1956 Vespa Motorbike. Design 150. Engine 150cc. Gas mileage 325.5. Professionally recovered by authorized Vespa auto mechanics. Special attention has actually been provided every specific throughout the whole reconstruction process, making use of ...3 weeks ago on AmericanlistedTools
-
"ORIGINAL OWNER" 1976 AMF HARLEY-DAVIDSON XLCH SPORTSTERI PURCHASED THIS BIKE NEW IN MAY OF 1976 FROM PANCIERA HARLEY IN BRADFORD RHODE ISLAND, SOLD IT IN 1989, AND BOUGHT IT BACK TO RESTORE IN ORIGINAL CONDITIONBIKE WAS CHANGED OVER TO RIGHT SIDE...2 weeks ago on AmericanlistedTools
-
Have one 1979 Iron head sporster Moter for sale this Moter have about 600 mile on a fresh rebuild The Heads bean ported and polish S&S lower end it is 86 inch have a nice powder coat on the heads and jugs rebuild trans this Moter is very HOT need ...Over 4 weeks ago on AmericanlistedTools
-
1981 cb6550c with under 22000 miles. Have the tool kit and owners manual.. new battery, charging rotor, carbs and brakes rebuilt. runs great used weekly. clean title.. please call 508-965-XXXX for more info..2 weeks ago on AmericanlistedTools
-
Exceptional condition BSA. Unrestored classic weekly rider. It has a 69 engine, new Avon tires, clutch replaced 500 miles ago. The speedometer works but reads about 8 mph slower than actual speed. The rims have some pitting. The gas tank looks ver...2 weeks ago on AmericanlistedTools
-
This is a 1973 Ossa Trials Bike. Frame up disassembly, sandblast and paint. New tires, Dunlop D803's, New brakes, cables, levers, wheel bearings, pegs, grips, bars, plastic fenders, custom seat, TLR shocks Explorer tank and more. Motor has been co...2 weeks ago on AmericanlistedTools
-
1982 Honda CB900 with 24,690 miles. Runs, drives and stops. Tires are a few seasons old however are in excellent shape. Battery is a few months old. Trigger plugs are also brand-new. Carbohydrates have been cleaned and have brand-new needles. The ...3 weeks ago on AmericanlistedTools
-
Up for auction we have a 1967 Triumph Trophy 650cc. This is a storage fresh time capsul built in the early 70s and has been sitting in storage since 1987 till I had recently found it.This bike has a rigid frame with a Girder Springer front HD spok...Over 4 weeks ago on AmericanlistedTools
-
… 1000 cc Iron Head XLCH..... Carlini Clean Sweep handle bars,Chrome controls,rebuilt S&S Super E carb (shorty).. Mustang seat,tapered turbo exhaust,chrome swing arm and lowering kit,highway pegs , electronic ignition ( Dyantek DS-1) ...2 weeks ago on AmericanlistedTools
-
1962 sportster restore or parts mostly original parts nice numbers but cracked casse and trans pilot shaft erea will need repair no carb or air cleaner rear fender was cut front fender was cut but have a piece to fix some seat post stuff no seat t...Over 4 weeks ago on AmericanlistedTools
-
I spoke to the mechanic who wrenched on it he said the bike was road worthy 3 years ago and said the knuckle ran very strong.2 weeks ago on AmericanlistedTools
-
Crankshaft ground and hard chromed New Pushrods, lifters, valves and valve springs Rebuilt carburetor M-441 Generator, distributor and electronic regulator by Indian Frank New accessory drive bushing and shaft.020 piston and rings New Hardware thr...2 weeks ago on AmericanlistedTools
-
1974 Triumph Trident, kept in a climate controlled environment and out of a serious collection. Currently registered and road-ready. Converted to a cafe-style bike. Very rare aluminium tank, 1969 ray gun mufflers, cafe style seat and custom paint....2 weeks ago on AmericanlistedTools
