-
1975 KTM 250. What you see is what I have...and how I got it. The engine is in a crate (no idea if it's all there)...cylinder skirt is broken (needs sleeved). No pipe. This is a cheater bike...stand the shocks up and run it in the vintage class,or...4 weeks ago on AmericanlistedTools
-
I acquired this project bike but don't have time to finish it. needs work or to be used for parts. has spark but is missing seat, cover for points housing, ignition switch, and other minor items. call for more info.4 weeks ago on AmericanlistedTools
-
This is a new / old stock tail light lens for most 1970's Puch mopeds, but will certainly work on a lot of 1970's mopeds like Batavus, Columbia, JC Penney Pinto, SPARTA, Foxi, FREE. Spirit, Motobecane, moby, Mobylette, Sachs, Kriedler, etc. I have...4 weeks ago on AmericanlistedTools
-
1978 Suzuki PE 175. Fresh leading End (Piston and tired Cyndrical tube). Weisco Forged Piston, Boyeson Fiberglass Reeds. 6 Speed close ratio which changes effortlessly. Runs Great, begins after 2-3 kicks, will idle after heated up, might require o...4 weeks ago on AmericanlistedTools
-
1980 AMF Roadmaster moped with 49cc Motari Minarelli 2 stroke engine.Runs and rides well,[pretty quick for a moped],the lights and horn are in working order.In very good original condition overall,the rear fender does have a piece broken off and t...4 weeks ago on AmericanlistedTools
-
Up for sale is a vintage DT-50M, 50cc Yamaha Dual-Sport motorcyle. I purchased this bike last year with the hope of a restoration. VERY cool (full-size frame) retro dual-sport that's liquid cooled as well as oil injected. The previous owner rode t...4 weeks ago on AmericanlistedTools
-
1968 Yamaha twin jet motorcycle for sale. Needs some tlc. I started to restore one side (left) of the gas tank from rust. I got around to take a carb off and saw its gunked up. Haven't got time to clean them out to fire it up. Engine has good comp...4 weeks ago on AmericanlistedTools
-
I bought this bike with hopes of restoring it but it's been in my garage for too long and needs to go now because I'm moving. It does not currently run and needs someone with mechanical experience and patience. It would also be a good parts bike. ...4 weeks ago on AmericanlistedTools
-
I have a collection of all new Krauser Bags which were planned as backup for a set placed on a 1982 Suzuki GS1100G. I offered the bike just before I ever had to replace the bags. If you require an established as replacement they are yours for $180...4 weeks ago on AmericanlistedTools
-
As it says,a xs650 roller that I was going to hard tail,but plans have changed.What you see is what you get.Most chrome should clean up,19"front wheel and 16"rear wheel.Bike was a disc brake front and rear.Would be a nice start for a bobber!I am d...4 weeks ago on AmericanlistedTools
-
1976/1979 Husqvarna Clutch Cover ,may fit other years, Small hairline crack, probably caused by the shift lever on the inside about 3/4 of an inch long. I also noticed a star crack ( like the kind that you get on your car windshield)probably cause...4 weeks ago on AmericanlistedTools
-
$ 300.00 Each.... Two Honda Gold Wing's Interstate models one is black and one is deep red maroonish... both need work will sell whole or for or by parts, cheap very very cheap ; near chicago, IL black one needs carb's worked and a starter; motor ...4 weeks ago on AmericanlistedTools
-
I have a Honda CB400a "Hondamatic" motorcycle without a title. I am selling it as a parts bike. This is the bike that has an automatic transmission with a high and low range - no clutch. It last ran in 2010 and has been sitting ever since. Mechani...4 weeks ago on AmericanlistedTools
-
1980 KZ 1000 LTD B. The bike is not currently running (lifeless electric battery). I'm not a mechanic however I believe that the camera chain is loosened and one cyndrical tube fouls the plug. The bike is not original it has actually been tweaked....4 weeks ago on AmericanlistedTools
-
VINTAGE 1977 KAWASAKI MOTORCYCLE ADVERTISEMENT for the KZ400, published in Mid-1977, FULL-Page Ad has 3 pictures of the KZ400 models including KZ400 SPECIAL & KZ400 STANDARD & KZ400 DELUXE, RAZOR TRIMMED & READY FOR FRAMING, measures approx 7-3/8'...4 weeks ago on AmericanlistedTools
