-
3-cylinder, low mileage, beautiful all original motorcycle. This bike has been sitting in a private collection for some time. 12,012 shown on odometer, 2-tone gold and black finish is good with a bit of wear on the pinstriping dividing the two. Ch...Over 4 weeks ago on AmericanlistedTools
-
, paint, tires, and 36MM flat side carbohydrates. New barnett clutch and springs. New chrome specification II growth chambers. Rebuilt top end. New Wiesco Pistons and rings..040 over. Aylor Engineering 120 H.P. H2 porting reed kit, resurfacing of ...2 weeks ago on AmericanlistedTools
-
1974 BMW R90/6 Caf Racer built by Editor Richard Backus of Motorcycle Classics and Dairyland Insurance in the 2013 Race-To-Rebuild Sweepstakes Series of the publication. I am the winner and proud owner of this gorgeous and wonderful motorbike. I h...2 weeks ago on AmericanlistedTools
-
1974 Ducati GT project1974 Ducati GT with 15,092 original miles frame # 756166 engine # 756082. The frame was just recently sand blasted and powder layered in gloss black and is in ideal condition. The motor turns over easily. Engine cases and all...2 weeks ago on AmericanlistedTools
-
1974 Ducati GT project1974 Ducati GT with 15,092 original miles frame # 756166 engine # 756082. The frame was recently sand blasted and powder coated in gloss black and is in perfect condition. The motor turns over freely. Engine cases and all eng...2 weeks ago on AmericanlistedTools
-
1974 Ducati GT project1974 Ducati GT with 15,092 original miles. The frame was just recently sand blasted and powder layered in gloss black and is in best condition. The motor turns over easily. Engine cases and all engine fins in fantastic condit...2 weeks ago on AmericanlistedTools
-
The Commando's vibration-beating Isolastic frame enabled Norton Villiers to successfully prolong the life of their hugely successful parallel twin. Launched in 1967, the Commando used the preceding Featherbed-framed Atlas model's 745cc engine and ...2 weeks ago on AmericanlistedTools
-
1974 vintage, is of the last year for the improved 850 model. Actually with a capacity of 828cc, the engine is of similar power, but far less stressed for increased rideability and reliability. The bike was subject to a full restoration some years...2 weeks ago on AmericanlistedTools
-
The bike offered here, of 1974 vintage, is of the last year for the improved 850 model. Actually with a capacity of 828cc, the engine is of similar power, but far less stressed for increased rideability and reliability. The bike was subject to a f...2 weeks ago on AmericanlistedTools
-
The Commando's vibration-beating Isolastic frame enabled Norton Villiers to successfully prolong the life of their hugely successful parallel twin. Launched in 1967, the Commando used the preceding Featherbed-framed Atlas model's 745cc engine and ...2 weeks ago on AmericanlistedTools
-
This is my 1974 Harley Davidson FLH complete custom. Modified stock 74 FLH frame. Functions an S&S 97 cubic inch stroker. 4 plug heads Dynatek single fire ignition Delkron cases S&S incredibly E carbohydrate Cycle Shack exhaust. 4 speed with Barne...2 weeks ago on AmericanlistedTools
-
1974 DUCATI 750 GT - FULLY RESTORED.1. Disassemble motor, clean, check all items for wear. The motor received very little in the way of new parts as the internals were in very good condition. Some new bearings were installed and file fitted first ...2 weeks ago on AmericanlistedTools
-
1974 Harley XLH 1000 Sportster. Matching numbers, super clean with low original miles. Original paint except for the front fender. Original exhaust system in excellent condition. New Mikuni carb conversion. I have the original carb and all associa...Over 4 weeks ago on AmericanlistedTools
-
1974 Kawasaki Z% done runs/ rides/ shift etc engine is completely rebuilt welded crank etc along with carbs , but needs finish work such as , fork reflector ( found it ) , tach harness , instrument cluster harness , horn and some minor stuff. I di...Over 4 weeks ago on ListedBuyTools
-
1974 Kawasaki Z1 900 95% done runs/ rides/ shift etc engine is completely rebuilt welded crank etc along with carbs , but needs finish work such as ,fork reflector ( found it ) , tach harness , instrument cluster harness , horn and some minor stuf...Over 4 weeks ago on Yupyi!Tools
